Search found 157 matches
- Tue Nov 14, 2017 11:45 am
- Forum: Automotive Air Conditioning Forum
- Topic: Two Condensers connected in series
- Replies: 21
- Views: 40260
Re: Two Condensers connected in series
This is not about the surface area of the condensers, but of the refrigerant tube internal restriction, e. g., for a 3/8" tube fabbed condenser: entry could be 2 parallel 3/8" tubes throughout. The second condenser could be 2 parallel tubes entry and half way a transition to a single 3/8&q...
- Tue Nov 14, 2017 11:17 am
- Forum: Automotive Air Conditioning Forum
- Topic: Two Condensers connected in series
- Replies: 21
- Views: 40260
Re: Two Condensers connected in series
I fabbed a dual condenser, supped up A/C'd Humvee. Condenser Basic Design Principals: A single condenser installation can be analyzed as 3 heat dissipators in series. 1) Initial heat disippator #1: Large internal flow flow cross sections for SENSIBLE heat transfer of superheated high vevocity gas on...
- Tue Oct 31, 2017 4:00 pm
- Forum: Automotive Air Conditioning Forum
- Topic: Printed a Shaft Seal Installer Tool on my 3D printer
- Replies: 10
- Views: 16208
Re: Printed a Shaft Seal Installer Tool on my 3D printer
CC Creator, Wish I had my snow cycle pictures to post. Centrifugal clutch with variable diameter sheaves to a jack shift and chain drive to rear axle with monster lightened sprocket. Wide Terra tires to plow through the CO snow high country during hunting season. All aluminum fabed frame (argon gas ...
- Sun Oct 29, 2017 6:54 pm
- Forum: Automotive Air Conditioning Forum
- Topic: Printed a Shaft Seal Installer Tool on my 3D printer
- Replies: 10
- Views: 16208
Re: Printed a Shaft Seal Installer Tool on my 3D printer
Diametric,
We're just funning and staying friendly,hope there is no offense.
It was just a thought for reward for service to this free web site (services performed:
"ACKITS.COM" grill ornament for TIM
"BRADFORD HERRICK" emblem for bohica's Salt Flats cycle
Hotrodac
We're just funning and staying friendly,hope there is no offense.
It was just a thought for reward for service to this free web site (services performed:
"ACKITS.COM" grill ornament for TIM
"BRADFORD HERRICK" emblem for bohica's Salt Flats cycle
Hotrodac
- Mon Sep 11, 2017 1:25 pm
- Forum: Automotive Air Conditioning Forum
- Topic: A slightly differnt A/C system
- Replies: 31
- Views: 46540
Re: A slightly differnt A/C system
Thinking about air cooled ventilated rotors or solid CO2 to cool multiple dry clutch stack using disk break type rotors
- Fri Sep 08, 2017 4:51 pm
- Forum: Automotive Air Conditioning Forum
- Topic: A slightly differnt A/C system
- Replies: 31
- Views: 46540
Re: A slightly differnt A/C system
7.2 for supercharger at 18
Above my pay grade but knew CR must be reduced. hope for your success
Are you going to Pikes Peak? I'll be there pretty soon
Above my pay grade but knew CR must be reduced. hope for your success
Are you going to Pikes Peak? I'll be there pretty soon
- Fri Sep 08, 2017 5:53 am
- Forum: Automotive Air Conditioning Forum
- Topic: A slightly differnt A/C system
- Replies: 31
- Views: 46540
Re: A slightly differnt A/C system
Oil separator improves evaporator heat transfer
Oil (liquid or foam) insulates the warm evaporator tube from the cold refrigerant and negates any imaginary benefit.
hotrodac
Oil (liquid or foam) insulates the warm evaporator tube from the cold refrigerant and negates any imaginary benefit.
hotrodac
- Thu Sep 07, 2017 8:20 am
- Forum: Automotive Air Conditioning Forum
- Topic: New Sanden squalling above 3000 rpm
- Replies: 11
- Views: 17107
Re: New Sanden squalling above 3000 rpm
I can purchase your 2850 crpm problem. Once made 508/5H14 acceptable by limiting suction valve opening, but difficult for you. Might back off anti rotation gear adjustment nut 15 degrees and restaking. See cutaway in "How to Air Condition Your Hot Rod" page 33. Mufflers are easier and simp...
- Thu Sep 07, 2017 7:53 am
- Forum: Automotive Air Conditioning Forum
- Topic: A slightly differnt A/C system
- Replies: 31
- Views: 46540
Re: A slightly differnt A/C system
"Oil flooded screw compressor" : So that is where you gained oil separator expertise. In early days I stopped radio noise from blower motor by installing diode between motor leads when changing between permanent vs series wound or viceversa.. York application has less than 2% oil circulati...
- Tue Sep 05, 2017 2:04 pm
- Forum: Automotive Air Conditioning Forum
- Topic: A slightly differnt A/C system
- Replies: 31
- Views: 46540
Re: A slightly differnt A/C system
Suspect he has an oil pumper or txv MOP defective. Goal for rotary wing is total of 50 lbs. so saved weight can divert to fuel (but now at 82 lbs.+). military version 50% of cooling is for electronics. They actually CNC the air fan for turbo axial rotary fan compactness. If we could design compact 1...