Search found 49 matches

by ice-n-tropics
Tue Nov 14, 2017 6:32 pm
Forum: Automotive Air Conditioning Forum
Topic: Two Condensers connected in series
Replies: 18
Views: 191

Re: Two Condensers connected in series

As Bohica indicated the a CAC, a hefty charge air cooler, is pretty basic for your higher temp and pressure intake air if you expect that HP and any engine life. You said lower ram air is for the radiator which leaves upper ram air for CAC and then Radiator. But not enough height for condensers w/o ...
by ice-n-tropics
Tue Nov 14, 2017 11:45 am
Forum: Automotive Air Conditioning Forum
Topic: Two Condensers connected in series
Replies: 18
Views: 191

Re: Two Condensers connected in series

This is not about the surface area of the condensers, but of the refrigerant tube internal restriction, e. g., for a 3/8" tube fabbed condenser: entry could be 2 parallel 3/8" tubes throughout. The second condenser could be 2 parallel tubes entry and half way a transition to a single 3/8&q...
by ice-n-tropics
Tue Nov 14, 2017 11:17 am
Forum: Automotive Air Conditioning Forum
Topic: Two Condensers connected in series
Replies: 18
Views: 191

Re: Two Condensers connected in series

I fabbed a dual condenser, supped up A/C'd Humvee. Condenser Basic Design Principals: A single condenser installation can be analyzed as 3 heat dissipators in series. 1) Initial heat disippator #1: Large internal flow flow cross sections for SENSIBLE heat transfer of superheated high vevocity gas on...
by ice-n-tropics
Tue Oct 31, 2017 4:00 pm
Forum: Automotive Air Conditioning Forum
Topic: Printed a Shaft Seal Installer Tool on my 3D printer
Replies: 10
Views: 723

Re: Printed a Shaft Seal Installer Tool on my 3D printer

CC Creator, Wish I had my snow cycle pictures to post. Centrifugal clutch with variable diameter sheaves to a jack shift and chain drive to rear axle with monster lightened sprocket. Wide Terra tires to plow through the CO snow high country during hunting season. All aluminum fabed frame (argon gas ...
by ice-n-tropics
Sun Oct 29, 2017 6:54 pm
Forum: Automotive Air Conditioning Forum
Topic: Printed a Shaft Seal Installer Tool on my 3D printer
Replies: 10
Views: 723

Re: Printed a Shaft Seal Installer Tool on my 3D printer

Diametric,
We're just funning and staying friendly,hope there is no offense.
It was just a thought for reward for service to this free web site (services performed:
"ACKITS.COM" grill ornament for TIM
"BRADFORD HERRICK" emblem for bohica's Salt Flats cycle
Hotrodac
by ice-n-tropics
Mon Sep 11, 2017 1:25 pm
Forum: Automotive Air Conditioning Forum
Topic: A slightly differnt A/C system
Replies: 31
Views: 2080

Re: A slightly differnt A/C system

Thinking about air cooled ventilated rotors or solid CO2 to cool multiple dry clutch stack using disk break type rotors
by ice-n-tropics
Fri Sep 08, 2017 4:51 pm
Forum: Automotive Air Conditioning Forum
Topic: A slightly differnt A/C system
Replies: 31
Views: 2080

Re: A slightly differnt A/C system

7.2 for supercharger at 18
Above my pay grade but knew CR must be reduced. hope for your success
Are you going to Pikes Peak? I'll be there pretty soon
by ice-n-tropics
Fri Sep 08, 2017 5:53 am
Forum: Automotive Air Conditioning Forum
Topic: A slightly differnt A/C system
Replies: 31
Views: 2080

Re: A slightly differnt A/C system

Oil separator improves evaporator heat transfer
Oil (liquid or foam) insulates the warm evaporator tube from the cold refrigerant and negates any imaginary benefit.
hotrodac
by ice-n-tropics
Thu Sep 07, 2017 8:20 am
Forum: Automotive Air Conditioning Forum
Topic: New Sanden squalling above 3000 rpm
Replies: 11
Views: 1101

Re: New Sanden squalling above 3000 rpm

I can purchase your 2850 crpm problem. Once made 508/5H14 acceptable by limiting suction valve opening, but difficult for you. Might back off anti rotation gear adjustment nut 15 degrees and restaking. See cutaway in "How to Air Condition Your Hot Rod" page 33. Mufflers are easier and simp...
by ice-n-tropics
Thu Sep 07, 2017 7:53 am
Forum: Automotive Air Conditioning Forum
Topic: A slightly differnt A/C system
Replies: 31
Views: 2080

Re: A slightly differnt A/C system

"Oil flooded screw compressor" : So that is where you gained oil separator expertise. In early days I stopped radio noise from blower motor by installing diode between motor leads when changing between permanent vs series wound or viceversa.. York application has less than 2% oil circulati...

Go to advanced search